Safety and limits
BenchPod runs at low voltages from USB-C, so it is safe to touch. These rules keep you, the pod, your computer and your board out of trouble. Read them once before you wire your first board.
Rules
- Never connect mains. ADC IN measures up to ±30 V and is not for mains or anything connected to mains. The BNC shell is the pod's ground, which connects to your computer through the USB cable.
- TARGET IN takes 2.7 to 20 V DC. Do not use a 24 V supply, and check the polarity: + on the left, GND on the right.
- 4-20 mA IN measures a current loop. Wire it in series with a transmitter. A supply wired straight to it overheats the input. From analog module v3r5 a current limiter holds the input at about 30 mA (28.5 to 31.5 mA) to protect the sense resistor; the reading then only shows that limit. Still do not do it.
- Check each plug before you push it in. Several terminal blocks take the same plug. Supplies go only to TARGET IN and the 4-20 mA OUT loop.
- DUT power can switch on at any time. Tests, CI pipelines, AI agents and the web app can turn it on remotely. Unplug the DUT power plug before you touch, probe or rework the board under test.
- Use wires rated for the current: up to 2 A on TARGET POWER 5V and 3.5 A on TARGET POWER EXT. Thin jumper wires get hot at those currents.
- Power it from a computer or a USB-C power supply with a CE or FCC mark, 5 V and at least 1.5 A (3 A when TARGET POWER 5V powers your board).
- Indoors, dry, on a non-conductive surface. Use the case, the stand or standoffs, not a bare metal bench. Keep cables under 3 m. Ethernet can be up to 30 m, indoors, to a switch or router in the same building.
- Keep the Wi-Fi bridge at least 20 cm (8 in) from people while it is on. It is made to sit on the bench next to the pod, not to be worn or held. It complies with FCC and ISED radiation exposure limits for an uncontrolled environment when used at 20 cm or more from your body.
- Not a toy. For adults; keep it, its plugs and its wires away from children.
Port limits
Port names match the labels on the case; a bare board without a case has the names in brackets printed on it. Full pin assignments are on Pin-out & connectors.
| Port | Rating | Never |
|---|---|---|
| USB-C IN (board: HOST / POWER) | 5 V in from a computer or USB-C power supply; also the pod's data link to the computer | A power source that is not a USB-C source |
| TARGET IN (board: EXT SUPPLY IN) | 2.7 to 20 V DC, + on the left | More than 20 V, or + and GND swapped |
| TARGET POWER 5V and TARGET USB (board: DUT 5V, both) | 5 V out, 2 A together | A supply connected to it (it is an output) |
| TARGET POWER EXT (board: DUT EXT) | TARGET IN switched out, 3.5 A (3 A on digital boards up to v3r3) | A supply connected to it (it is an output) |
| WI-FI BRIDGE (board: BRIDGE POWER) | 5 V out, 1 A, for the Wi-Fi bridge | A supply connected to it |
| TARGET I/O, LA1 to LA14 (board: I/O HEADER) | 1.8 V or 3.3 V, the I/O voltage you set | A signal above the I/O voltage you set |
| ADC IN (BNC) | ±30 V | Mains, or any circuit connected to mains |
| DAC OUT | Outputs: 0 to 3.3 V, 0 to 5 V, ±12 V | A voltage or supply connected to an output |
| 4-20 mA IN | Current input, up to 24 mA (from analog module v3r5: limited to about 30 mA) | A supply connected straight to it, with no transmitter in the loop |
| 4-20 mA OUT | Two-wire output, external floating loop supply of 12 to 30 V | A loop supply above 30 V, or anything in the loop tied to the pod's ground |
Something got hot, smoked or hurt someone?